齊一生物試劑盒組分經過重重優化，每個組分的穩定性都完美的經過高溫破壞測驗，程度的避免了長途運輸和保存過程中抗原抗體的失活.齊一生物試劑盒憑借其完美的標曲.嚴格的質控.穩定高、易保存，操作簡便，已廣泛應用在全國免疫學檢驗研究所的各領域中.深受研究者們的青睞. 齊一生物銷售：021－6034 8496；181214 53965；173021 04490

【小鼠C肽(C-Peptide)ELISA試劑盒】齊一生物試劑盒憑借其完美的標曲、嚴格的質控、較高的穩定性，在世界范圍內的科研試劑領域中脫穎而出深受研究者們的青睞. 齊一生物銷售：021－6034 8496；181214 53965；173021 04490

【友情提示】：本產品僅供科研研究使用，不得用于人體臨床直接檢測。避免給您帶來不必要的損失，請仔細閱讀購買說明！

試驗所需自備物品:

1. 酶標儀(450nm 波長濾光片)

2. 高精度移液器，EP 管及一次性吸頭

3. 37℃恒溫箱，雙蒸水或去離子水

4. 吸水紙

【小鼠C肽(C-Peptide)ELISA試劑盒】試劑盒安全性提示：

1.工作人員實驗中避免直接接觸終止液和底物A、B。一旦接觸到這些液體，請盡快用水沖洗。

2.實驗中不要吃喝、抽煙或使用化妝品。

3.不要用嘴吸取試劑盒里的任何成份。

操作注意事項：

1.試劑盒應按標簽說明書儲存，使用前恢復到室溫30分鐘后方可使用。稀稀過后的標準品應丟棄，不可保存。

2.實驗中不用的板條應立即放回包裝袋中，密封保存，以免變質。

3.不用的其它試劑應包裝好或蓋好。不同批號的試劑不要混用.請?jiān)谠噭┖斜Ｙ|(zhì)前使用。

4.使用一次性的吸頭以免交叉污染，吸取終止液和底物A、B液時，避免使用帶金屬部分的加樣器。

5.使用干凈的塑料容器配置洗滌液。使用前充分混勻試劑盒里的各種成份及樣品。

6.洗滌酶標板時應充分拍干，不要將吸水紙直接放入酶標反應孔中吸水。

7.底物A應揮發，避免長時間打開蓋子。底物B對光敏感，避免長時間暴露于光下。避免用手接觸，有毒。實驗完成后應立即讀取OD值。

8.加入試劑的順序應一致，以保證所有反應板孔溫育的時間一樣。

9.按照說明書中標明的時間、加液的量及順序進行溫育操作。

【小鼠C肽(C-Peptide)ELISA試劑盒】齊一生物供應ELISA試劑盒檢測的目的是為實驗提供準確可靠的定量分析實驗依據。為了保證實驗數據的可靠性，在實驗過程中必須堅持全面質量控制和全過程質量控制。在收集標本前都必須有一個完整的計劃。

操作步驟
實驗開始前，請?zhí)崆芭渲煤盟性噭�，試劑或樣品稀釋時，均需混勻，混勻時盡量避免起泡。每次檢測都應該做標準曲線。如樣品濃度過高時，用樣品稀釋液進行稀釋，以使樣品符合試劑盒的檢測范圍。
1.         加樣：分別設空白孔、標準孔、待測樣品孔�？瞻卓准訕悠废♂屢�100μl，余孔分別加標準品或待測樣品100μl，注意不要有氣泡，加樣將樣品加于酶標板孔底部，盡量不觸及孔壁，輕輕晃動混勻，酶標板加上蓋或覆膜，37℃反應120分鐘。
為保證實驗結果有效性，每次實驗請使用新的標準品溶液。
2.         棄去液體，甩干，不用洗滌。每孔加生物素標記抗體工作液 100μl（取1μl生物素標記抗體加99μl生物素標記抗體稀釋液的比例配制，輕輕混勻，在使用前一小時內配制），37℃,60分鐘。
3.         溫育60分鐘后，棄去孔內液體，甩干，洗板3次，每次浸泡1-2分鐘，350μl/每孔，甩干。
4.         每孔加辣根過氧化物酶標記親和素工作液（同生物素標記抗體工作液） 100μl，37℃，60分鐘。
5.         溫育60分鐘后，棄去孔內液體，甩干，洗板5次，每次浸泡1-2分鐘，350μl/每孔，甩干。
6.         依序每孔加底物溶液90μl，37℃避光顯色（30分鐘內，此時肉眼可見標準品的前3-4孔有明顯的梯度藍色，后3-4孔梯度不明顯，即可終止）。
7.         依序每孔加終止溶液50μl，終止反應（此時藍色立轉黃色）。終止液的加入順序應盡量與底物液的加入順序相同。為了保證實驗結果的準確性，底物反應時間到后應盡快加入終止液。
8.         用酶聯儀在450nm波長依序測量各孔的光密度（OD值）。 在加終止液后15分鐘以內進行檢測。
【小鼠C肽(C-Peptide)ELISA試劑盒】注：
1. 用戶在初次使用試劑盒時，應將各種試劑管離心數分鐘，以便試劑集中到管底。
2. 每次實驗留一孔作為空白調零孔，該孔不加任何試劑，只是*后加底物溶液及2N H2SO4。測量時先用此孔調OD值至零。
3. 為防止樣品蒸發，試驗時將反應板放于鋪有濕布的密閉盒內，酶標板加上蓋或覆膜。
4. 未使用完的酶標板或者試劑，請于2-8℃保存。標準品、生物素標記抗體工作液、辣根過氧化物酶標記親和素工作液請依據所需的量配置使用。請勿重復使用已稀釋過的標準品、生物素標記抗體工作液或、辣根過氧化物酶標記親和素工作液。
5. 建議檢測樣品時均設雙孔測定，以保證檢測結果的準確性。
以上資料僅供您參考，如有問題歡迎來電，齊一生物銷售：021－6034 8496；181214 53965；173021 04490

9240241Housing, disposable tip adapter, TRCNY

9239957EZ1, PM ServiceService covers all travel ａnd labor costs plus all necessary parts to perform a Preventative Maintenance. The instrument will also be thoroughly checked ａnd inspected to determine if any additional parts are required to get the instrument running to its optimal performance. There will be an additional charge for any such parts if any are needed.CNY

9239566Packaging, LX100 Optics PlatformCNY

9239558Spring, XYP Torsion Door (Set of 5)CNY

9019925PCB, Mainboard (Microbrd not incl.), CxxCNY

9238867Premium Cover Agreement MDx, 2PM, 1yrThe Premium Cover Agreement MDx, 2PM provides full service coverage for the BioRobot MDx. Costs for service visits are fully covered including travel, labor, ａnd parts. The agreement also includes two annual preventive maintenance visits, with costs for labor ａnd parts covered. With a Full Agreement, there is a priority response time of 24 hours (1 working day).CNY

9241213Full Agreement Depot Repair, PtWash, 1yr"The Full Agreement Depot Repair, PtWash provides full service coverage for the plate washer used in the digene HPV application. The service is conducted as an instrument exchange service. 

All shipping, labor ａnd repair part costs related to an instrument exchange are included for 1 year. Instrument exchange time is 2 - 3 working days."CNY

9241199QIAxcel, Full Agreement, no PMThe Full Depot Repair Agreement, QIAxcel covers all shipping, labor ａnd repair part costs related to an instrument repair for 1 year. Service turn around time is 7-10 working days.CNY

9238821Rect.  carrier for 2 Falcon tubes 50 mlCNY

9019469COMB CASTING 0.2MM X 52 WELLSCNY

9243649Acceler. Valid Support, Other Quant. SysThe QIAGEN Accelerated Validation Support Other Quantification System service includes all travel ａnd labor charges for a site visit up to 5 days by a QIAGEN Applications Specialist.  A QIAGEN specialist will provide hands-on user reaction setup, ａnd best practices.  The Accelerated Validation service includes guidance on the laboratory’s validation experimental design, internal validation documentation support, ａnd QIAGEN sponsored templates.  The QIAGEN Specialist will also aide the customer in running some samples to initiate the validation process.  The customer is responsible for final documentation ａnd report using QIAGEN prepared templates provided with the final product. Enough consumable chemistry ａnd accessories (QIAGEN or other vendors) should be purchased by the customer to cover the validation experimental design ａnd are not included in the cost of validation support. Please indicate which protocols to validate (Plexor HY, Quantifiler Human, Quantifiler Y, Quantifiler Duo)CNY

9233373Spring, gas-driven, cover, BR8000CNY

9233339Valve, throttleCNY

9237335BR MDx, Full AgreementThe Full Agreement MDx provides full service coverage for the BioRobot MDx. Costs for service visits are fully covered including travel, labor, ａnd parts. The agreement also includes one annual preventive maintenance visit, with costs for labor ａnd parts covered. With a Full Agreement, there is a priority response time of 48 hours (2 working days).CNY

9237148XYP FanCNY

9237136#Twister II, Full Agreement, no PMThe Full Agreement BR Twister II provides full service coverage for the BioRobot Twister II. Costs for service visits are fully covered including travel, labor, ａnd parts. With a Full Agreement, there is a priority response time of 48 hours (2 working days).CNY

9237128Upgrade App., RNeasy 96, BR8000CNY

9237119Upgrade App., MagAttract MiniprepCNY

9237105Protocol Dev./Opt., on-site (1-day)The QIAGEN BioRobot Systems Protocol Development/Optimization On-Site Visit includes all travel ａnd labor charges for a site visit up to 8 hours by a QIAGEN Instrumentation Service Specialist to write and/or opimize protocols for the BioRobot System. Parts, consumable chemistries, ａnd accessories not included. Custom protocols are the sole responsibility of the customer ａnd neither warrantied nor guaranteed.CNY

9236419Buzzer, TWICNY

9236411Fingers, deepwell, kit, TWICNY

9232967Board, X-main adapter, BR8000 v1.00CNY

9232951Bar code reader adapter Board, E10084CNY

9236360Syringe Cylinder with Seal"syringe cylinder ａnd seal for Luminex. We apparently do not sell the seal separate from the cylinder. These items are replaced at annual PM＇s, but customer＇s may want to replace them more often ａnd would be responsible for paying for them on their own then.

Source: Glen"CNY

9232920Card, x-main, PCON, v1.04CNY

9232914PCB, RS232, X-mainCNY

9236349375mA Fuse sensor distribution BoardCNY

9236332CompressorCNY

9236322Air SolenoidCNY

9236162O-Ring, replacement kit, RapidPlateCNY