產品展示
彈射動能測試儀生產供應商地址,優質售貨點
點擊次數：107發布時間：2013/12/9 16:24:23
更新日期：2019/9/23 15:38:15
所 在 地：中國大陸
產品型號：彈射動能測試儀
相關標簽：彈射動能儀 動能彈射測試儀
優質供應
詳細內容
動能彈射測試儀/玩具彈射動能測試儀
彈射動能測試儀應 用：
測速式彈射動能測試儀，適用于彈射物、蓄能彈射玩具、非蓄能彈射玩具的動能測試如玩具槍，玩具飛船，玩具弓弩等
彈射動能測試儀 的詳細介紹
標準配置：
動能儀 1 臺，外傳感器 1套，外傳感器支架1套，電源線 1根，操作說明書 1本。
產品具體參數如下：
1.電源 200/220 AC / 50Hz.
2.外型尺寸 : 36cm x 31cm x 18cm.
3.時間顯示：0.00000
4.焦耳：0.0000e+00J
5.彈射物直徑：大0.5mm —小于40mm.（內部傳感器）.
6.內通道行程： 100mm
7.外部傳感器距離：40mm— 400mm（可調）.
本儀器符合以下標準:
ASTM:F963-03 EN-71-03
*LED顯示屏。
*自動記錄10組成數據。
*通道內任意位置測量，不受物體居中測量限制。
TNC40B帶打印
萬能材料試驗機、耐磨試驗機、落球沖擊試驗機、插拔力試驗機、扭力試驗機、筆記本轉軸壽命試驗機按鍵壽命試驗機、手機翻蓋滑蓋試驗機、觸摸屏點擊劃線試驗機、手機軟壓試驗機、手機跌落、破裂強度、紙箱抗壓試驗機、破裂強度試驗機、單/雙臂跌落試驗機、電線耐磨試驗機、曲折.突拉試驗機、線材伸長率、聽筒線伸縮疲勞試驗機、擺錘沖擊、杜邦沖擊、水平垂直燃燒試驗機、針焰試驗機、灼熱絲試驗機等
The Ejection kinetic energy tester
Ejection kinetic energy tester is also called （kinetic energy tester, tester ejection kinetic energy, kinetic energy tester, bullet ejection tester）
For the amount of kinetic energy test ejection toys, ejection toys to components by test tube instrument or after two induction external test components, the measured toys ejection parts after a certain distance of time, its kinetic energy calculation. The instrument is mainly used for safety performance inspection ejection toys for baby or child.
This device complies with the following standards: ASTM F 963-08
EN-71-05
Notes: for testing involves some materials from the launch of the toys ａnd toys from the launch of a non exclusive projectiles may cause, but not all, potential risk of accidents.
1 power: 220AC/50Hz.
2 dimensions: 240mm * 310mm * 130mm.
3: 1MHz crystal
4 time display number: 7.
5 display range: 0.000001 to 9.999999 sec.
6 fire channel size: 60MM diameter （channel）
The 7 sensor distance:
Channel: a fixed 150mm sensor: adjustable 40mm-420mm
8 internal sensor sensitivity: more than 2mm
The testing process
1.1 connect the power to display 0.
1.2 according to the sample selection using external sensors or internal sensor. If you choose the external sensor, will choose to switch to the EXT file, if the choice of cylinder sensor, then go to the int file
1.3 the use of internal sensor
1） the external sensor removed; ｓelect switch to the int file
2） to conduct pre testing, to test toys level through the internal test tube, observe the display reading. The readings for the time value, 0 seconds.
3） if there is no display, may be due to the low sensitivity of sensor, sensor does not sense. Regulation of D as shown in Figure 1, the E knob clockwise, counterclockwise rotation increases the sensitivity, the sensitivity decreases. D front sensor adjustment knob, E rear sensor adjustment knob. Sensitivity should be appropriate, too small will affect the test.
4） sensitivity adjustment is completed, test. To be measured through toys level test cylinder, the readout time. Before ａnd after the 100mm distance between sensors, calculated the speed measured toy, ａnd then calculate the degree of kinetic energy.
5） test the safety coefficient of toys to meet required standards.
1.4 the use of external sensors
1） G interface connected to the external sensor is shown in figure 2. With your fingers or other objects move in the in front of the sensor, sensor at the top of the red light is normal. If not light possible connection is not bright. Pull out, inserted again. The sensors work well will be joint locking.
2） the sensor mounted to the bracket, adjusting the distance between the two sensor, ａnd the bracket is convenient for testing position.
3） for test. The toy levels through sensor front-end tested, display process start time, stop time. Adjust the sensitivity of the sensor, front rotation corresponding rear left interface, back interface corresponding to the right end of the knob.
4） sensitivity adjustment is completed, test. To test toys levels through the front end of the sensor, the reading display reading speed ａnd kinetic energy calculation, toys.
5） safety judgment does not conform to standards of toys.
The Ejection kinetic energy tester
http://www.astmf963.com/product_181.html
